인류의 건강과 생명공학 발전을 위해 봉사하는 기업 드림셀
We Serving the Health and Biotechnology of Humanity
홈 > 제품정보 > 시약 > 해외 공식 대리점 > [SEA633Mu] ELISA Kit for Platelet Derived Growth Factor BB (PDGF BB)
[SEA633Mu] ELISA Kit for Platelet Derived Growth Factor BB (PDGF BB)
제품코드 : SEA633Mu
제품정보 : Cytokine;Tumor immunity;
- Organism Species: Mus musculus (Mouse)
- Sample Type: Serum, plasma and other biological fluids
- Test Method: Double-antibody Sandwich
- Assay Length: 3h
- Detection Range: 0.156-10ng/mL
- Sensitivity: The minimum detectable dose of this kit is typically less than 0.062ng/mL
제품문의
-
- 전화번호
- 2292-8870
- 이메일
- dreamcell@dreamcell.co.kr
제품상세
Specificity
This assay has high sensitivity and excellent specificity for detection of Platelet Derived Growth Factor BB (PDGF BB).
No significant cross-reactivity or interference between Platelet Derived Growth Factor BB (PDGF BB) and analogues was observed.
Recovery
Matrices listed below were spiked with certain level of recombinant Platelet Derived Growth Factor BB (PDGF BB) and the recovery rates were calculated by comparing the measured value to the expected amount of Platelet Derived Growth Factor BB (PDGF BB) in samples.
| Matrix | Recovery range (%) | Average(%) |
| serum(n=5) | 80-98 | 84 |
| EDTA plasma(n=5) | 89-103 | 101 |
| heparin plasma(n=5) | 81-98 | 85 |
Precision
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Platelet Derived Growth Factor BB (PDGF BB) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Platelet Derived Growth Factor BB (PDGF BB) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%
Linearity
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Platelet Derived Growth Factor BB (PDGF BB) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.
| Sample | 1:2 | 1:4 | 1:8 | 1:16 |
| serum(n=5) | 88-95% | 92-99% | 78-99% | 96-105% |
| EDTA plasma(n=5) | 78-101% | 83-90% | 78-101% | 80-104% |
| heparin plasma(n=5) | 92-101% | 88-95% | 81-99% | 81-91% |
Stability
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Reagents and materials provided
| Reagents | Quantity | Reagents | Quantity |
| Pre-coated, ready to use 96-well strip plate | 1 | Plate sealer for 96 wells | 4 |
| Standard | 2 | Standard Diluent | 1×20mL |
| Detection Reagent A | 1×120µL | Assay Diluent A | 1×12mL |
| Detection Reagent B | 1×120µL | Assay Diluent B | 1×12mL |
| TMB Substrate | 1×9mL | Stop Solution | 1×6mL |
| Wash Buffer (30 × concentrate) | 1×20mL | Instruction manual | 1 |
Assay procedure summary
1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.